(photo: Cintec North America)
10.12.2020, 21:22

Fire Resistance in Anchor Systems

Architecture, Construction, Fire Safety, Life Safety

Despite the welcome focus on the safety of cladding following the UK’s Grenfell Tower tragedy, Cintec North America is cautioning specifiers to consider the fire resistance of remedial anchors and reinforcements used in building renovation.


In the past few years, fire has been an increasing concern when buildings are being retrofitted, restored, or modernized.


On June 14th, 2017, a fire broke out in the 24 storey Grenfell Tower, widely reported as the worst residential fire to take place in the United Kingdom since the second World War, due to failures by design.


As concerns over fire safety spread through the country, Prime Minister Theresa May ordered a public inquiry. As stated in the final report of the review of building regulations and fire safety, England is by no means alone in needing to improve building safety, as building regulations are a global concern.


Under the terms of the EC Construction Products Directive, resistance to fire is one of the essential requirements for which performance tests are required. In Europe, thin-joint mortars have become popular, thus there are a number of situations where fixings are made using organic polymers as either the tie body, or in the form of resin glues. Such ties are not inherently fire resistant and could fail and shorten the life of a cavity wall in a fire, or lead to the collapse of cladding resulting in danger to escaping occupants and fire fighters.


As a leader in structural preservation, Cintec has always been an advocate for the restoration of safe buildings through fire-resistant anchors, as long ago as 1993 fire tests were carried out by the internationally recognized Building Research Establishment in accordance with BS476([1]), ISO([2]), and CEN([3]). The fire rig was designed for use in the measurement of the performance of Cintec’s™ anchors in a fire situation while subjected to a mechanical load which might be a result of wind suction of fire-induced thermal movement.


Cintec’s remedial anchors survived a two-hour test without failure of any of the samples. Every sample reached several hundred degrees in the part of the anchor nearest to the fire face. This indicates the anchor system can be recommended for repair work to buildings requiring a fire rating of up to two hours.


Cintec Anchors were later, unintentionally, put to the test at the Fullers Brewery in London. The Cintec anchor system had been used extensively to repair and restore the Brewery’s facade. A fierce fire followed, destroying large sections of the building. Despite the brickwork being subjected to extremely high temperatures, tests revealed that the cementitious Cintec anchors did not fail, performing to their original design. They retained their integrity and could be reused for the repair work. If the anchors were an epoxy or resin type, they would have melted, releasing potentially dangerous fumes in the process and have been easily pulled out, allowing the wall to collapse. One could say that the Cintec Anchors having survived the fire are in fact fire proof.                                  


In New York City, according to the NYC Buildings Department, adhesive anchors are not permitted to support fire-resistance rated construction unless the use of such anchors meets the conditions set forth in the acceptance criteria. Post-installed anchors in masonry must be designed in accordance with the NYC Construction Codes, describing the masonry substrate type and condition, as well as proof of pull tests.


Howard Zimmerman, the well-known NY Architects, had concerns about the lack of fire ratings for resin-based anchor systems in high rise apartments near Central Park, New York. After reviewing Fire Test Data and performance tests on a severely damaged building after a fire, it was determined that the Cintec System was the best anchor to meet the project engineers’ concerns.


As a fire-resistant alternative to resin anchors, Cintec anchors are based on restoration materials, cementitious grout and stainless steel and provide the elusive fire rating that is typically absent in other systems.




[1] BS476: Part 20: 1987, Fire tests on building materials & structures. British Standards Institute, London, 1987

[2] ISO/DIS 834 - Fire resistance tests – Elements of building construction. Part 1: General requirements for fire resistance testing; Part 2: Fire resistance testing of non-loadbearing elements; Part 3: Fire resistance testing of loadbearing elements

[3] CEN prENYYY1, prENYYY2, prENYYY3 (Renumbered equivalents of ISO drafts). 




Article rating:

vote data

Leave a reply

 (photo: Polyteck Group)
News Editor  - 30.09.2021

Residential PPM Contract Award

Polyteck Group has secured a one-year contract to provide planned preventive maintenance (PPM) services at Lillie Square, a new landscaped residential development in West London in the latest of a...

Pictured (L-R): New apprentices, Thomas Gordon, Emma Walker and Manveer Sangha. (photo: Mitie Group)
News Editor  - 28.09.2021

Mitie Welcomes Technical Apprentices

Mitie has surpassed a target of recruiting 50 new technical apprentices in 2021 with the addition of a new intake of 41 apprentices to its Technical Services Apprenticeship Programme.

 (photo: Compass Group UK & Ireland)
News Editor  - 18.12.2020

Providing 20,000 Meals to Those in Need

The Wimbledon Foundation has extended its support for organisations addressing food poverty at Christmas and beyond as part of its response to COVID-19.

 (photo: CPD Global)
News Editor  - 18.12.2020

Ecolab Named to CDP A Lists

The Carbon Disclosure Project (CDP) has added Ecolab to its A List for Climate, as well as Water Security.

 (photo: Bodet SA)
News Editor  - 17.12.2020

Enhancing Home Worker Visibility

Bodet have extended the coverage of the Kelio time and attendance software solution to staff working at home.